WWW.DISSERTATION.XLIBX.INFO
FREE ELECTRONIC LIBRARY - Dissertations, online materials
 
<< HOME
CONTACTS



Pages:   || 2 |

«READ AND SAVE THESE INSTRUCTIONS CAUTION: Before using this product, read this manual and follow all safety rules and operating instructions. Failure ...»

-- [ Page 1 ] --

16” Outdoor Misting/Oscillating Fan

Model Number: AMMF16R

Owner’s Manual

READ AND SAVE THESE INSTRUCTIONS

CAUTION:

Before using this product, read this manual and follow all safety rules and operating instructions. Failure

to comply with instructions could result in personal injury and/or property damage.

IMPORTANT:

For replacement parts or assembly questions call 1-800-320-6478 or go to www.auramist.net AMMF16R Rev. A 07/10 1 Table of Contents

SECTION PAGE

1. Safety Information …………….……………………………………………………….……………..2

2. Carton Contents……………………………………………………………………….….….……….…...5

3. General Assembly Instructions ……………………………………….……………………..……....…..6

4. Operation Instructions…………………………………….……………..……………..………...…..7

5. Maintenance………………………………………………………………….…………………...…..9

6. Storage…………………………..…………………………………………….…………….…...…...11

7. Troubleshooting…………………………..…………………………………….………………..……11

8. Exploded View

9. Parts List… ……………………….……………………….….……………

10. Warranty ……………..……………………………………………….………...………………….....14 Safety Warnings

READ AN SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

Household Type

SAVE THIS MANUAL FOR FUTURE REFERENCE.

READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE.

Read and understand this instruction manual and all labels on the misting fan before using.

Safety is a combination of common sense, staying alert and knowing how this misting fan works. Use this misting fan only as described in this manual. To reduce the risk of personal injury or damage to the misting fan, use only recommended accessories.

Understanding Safety Terminology DANGER: If safety information is not followed, someone will be seriously injured or killed.

WARNING: If safety information is not followed, someone could be seriously injured or killed.

CAUTION: If safety information is not followed someone may be injured.

When using this misting fan follow basic safety precautions including the following:

–  –  –

WARNING: DO NOT USE THE MISTING ON-OFF SWITCHES AS THE MEANS

OF DISCONNECTING POWER WHEN INSTALLING OR SERVICING THIS PRODUCT.

ALWAYS DISCONNECT THE POWER CORD.

8. Disconnect the power cord before moving or performing any maintenance on the misting fan.

9. This misting fan shall not be used in potentially dangerous conditions, such as flammable, explosive or chemically loaded atmospheres.

10. Do not use or store near hazardous materials.

11. Completely assemble the misting fan according to these instructions before connecting to the power source.

12. If the misting fan is not working correctly, has missing parts, has been dropped or damaged, left outdoors or dropped in water, call an authorized service center for evaluation, adjustment or repair.

WARNING: IMPROPER CONNECTION OF THE EQUIPMENT-GROUNDING

CONDUCTOR CAN RESULT IN A RISK OF ELECTRICAL SHOCK. CHECK WITH A

QUALIFIED ELECTRICIAN OR SERVICE PERSON IF YOU ARE IN DOUBT AS TO

WHETHER THE OUTLET IS PROPERLY GROUNDED. DO NOT MODIFY THE PLUG

PROVIDED WITH THE MISTING FAN IF IT WILL NOT FIT THE OUTLET; HAVE A

PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN. DO NOT USE A

THREE-PRONG TO TWO-PRONG ADAPTER. IMPROPER CONNECTION MAY CREATE

A RISK FOR ELECTRICAL SHOCK.

13. This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace the fuse per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded or returned to an authorized service facility for examination and/or repair.”

14. To protect against electrical shock, do not immerse unit, plug, or cord in water or spray with liquids.

15. Keep the cord away from heated surfaces.

16. To reduce the risk of injury from the misting fan accidentally starting, unplug the power cord before replacing the filter.





17. Do not leave the misting fan unattended when it is plugged in. Unplug it from the power outlet when not in use and before servicing. Turn off the misting fan before unplugging.

AMMF16R Rev. A 07/10 3

18. Do not operate the misting fan with a damaged power cord, plug, or if the misting fan is damaged in any manner. Call an authorized service center for evaluation, adjustment or repair.

19. Do not run cord under carpets. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.

20. Do not insert or allow any foreign objects to enter the intake or exhaust air openings, as it may cause mechanical, electrical, or fire damage to the mist fan.

21. Do not block or tamper with the misting fan nozzles, as it may reduce or impede the functionality or quality of the mist. Call an authorized service center for evaluation, adjustment or repair.

22. Always place the misting fan on a stable flat surface to avoid the chance of tipping.

23. Never place the misting fan where it may fall into a water reservoir (example: bathtub or pool), or anything containing an electrical conductive substance.

24. When the product is used outdoors, use only on GFCI (Ground Fault Circuit Interrupter) protected receptacles.

25. This product must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. Plug into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

26. Avoid contact with moving parts.

27. Do not hang or mount misting fan on a wall or ceiling.

28. Do not operate without misting fan guards properly in place.

–  –  –

1. Ensure that the power cord is disconnected from the power outlet.

2. Align misting fan pole to the base hole to the front direction of the base. Gently push the hose and power cable of the air pump aside and press the mist fan pole until the screw hole is aligned. (fig. 1).

Make sure you do not kink the hose in this process. Deleted: kinked

3. Fasten the misting fan pole assembly to the power base assembly with the two screws (fig.1).

4. Fasten the misting fan pole assembly to the power base assembly with the pole screw (fig.2).

5. Loosen the pole lock knob and pull the inner pole out. Tighten the lock knob and attach the mist fan assembly to the inner center pole and fasten screw knob (fig. 3).

6. Disassemble the rear misting fan guard nut (rotate counterclockwise) and the misting fan blade nut (rotate clockwise) from the misting fan head assembly (fig.4).

7. Align the rear fan guard hole to the three pins on the motor housing, and fasten the rear fan guard to the fan head assembly with the rear fan guard nut (figure 5).

8. Mount the fan blade to the fan motor shaft (fig.6). Make sure the fan blade gap aligns with the pin clip Formatted: Indent: First line: 0 ch on the motor shaft and then screw on the blade nut (fig.7). Mount the front guard and tighten all the hinges Deleted: around outer rims of the fan guard (figures 8 & 9).

9. Connect nozzle housing by gently sliding the nozzle housing into the holder on the front fan guard (fig.10)

10. Connect the air and water tubes to the connectors on the misting fan pole assembly. The water is the smaller tube. Make sure the tube is pushed all the way into the connector, and then make the electrical connection (fig.11) AMMF16R Rev. A 07/10 6 Operating Instructions IMPORTANT: Read this owner’s manual before operating this product.

THE MISTING FAN IS INTENDED FOR OUTDOOR USE BUT MAY BE USED INDOOR

WITHOUT THE MISTING FEATURE.

Place the misting fan on a level surface near an electrical outlet. Place the misting fan out of reach of children. Do not insert anything into the grill. If moving the misting fan to a different location, turn it OFF and unplug it from the socket.

1.To operate the misting mist fan, plug the power cord into a 120 VAC, 60Hz outlet.

CAUTION: MIST FAN AND/OR MISTING SYSTEM MAY START UP WHEN THE

UNIT IS INITIALLY PLUGGED TO THE POWER OUTLET.

2. Fan Operation (ON-OFF, Speed control) Press the button to Low, Medium, High, or OFF to select fan speed. (fig.1)

3. Fan Operation (Oscillation Control) To operate the oscillation function, press down the oscillation switch. To stop the oscillation function, pull-up the oscillation switch. The oscillation angle is approximately 65 degrees (fig. 2).

4. Misting Operation IMPORTANT: This product is designed to operate with city water supply.

Make sure your water pressure is lower than 100 PSI. 40 to 80 PSI water pressure will ensure optimal functionality of the system throughout maintenance intervals. The misting fan and/or misting system may start up when the unit is initially plugged to the power outlet.

DO NOT USE THE MISTING FEATURES INDOORS.

–  –  –

Misting ON/OFF control Mist ON Press the rocker switch to the ON position. (fig. 5)/ Turn the ball valve to the ON position (fig. 6) Open the flow control valve until mist is visible, then refer to ADJUSTING MIST DENSITY section, to get an optimal mist performance. (fig.7) Mist OFF Turn the ball valve to OFF position (fig.8) To prevent the accumulation of mineral deposits, let the pump run for 2 minutes after closing the ball valve so the air pump can clear the remaining water from the nozzles. Turn the pump switch to the OFF position when complete. (fig.9) AMMF16R Rev. A 07/10 8

ADJUSTING MIST DENSITY

CAUTION: Do not over tighten and/or loosen the water flow control valve.

The misting function of this fan is adjusted by rotating the flow control valve on the fan pole assembly counter clockwise to decrease mist density or counter-clockwise to increase mist density. It may take a minute for a new misting fan to start misting. It is normal for air to come out of the nozzles before water and the mist.

To optimize the cooling effectiveness of the system, you can:

• Operate the unit with a DRY or WET mist, based on your needs.

• To increase the mist density, turn the mist control valve counterclockwise. (fig.10)

• To decrease the mist density, turn the mist control valve clockwise. (fig.11)

5.Operating Tips For dry climates, increasing the water flow will provide maximum cooling results. In humid climates, a reduced water flow is recommended.

–  –  –

CUSTOMER RESPONSIBILITIES

Read and follow the maintenance schedule and the maintenance procedures listed in this section.

WARNING: ALLWAYS UNPLUG THE POWER CORD BEFORE MOVING OR

SERVICING THE MISTING FAN.

WARNING: DO NOT IMMERSE THE MISTING MIST FAN IN WATER!

REPLACING FILTERS

WARNING: ANY SERVICING OF THIS UNIT, EXCEPT FOR GENERAL

MAINTENANCE DESCRIBED IN THIS SECTION, SHOULD BE PERFORMED BY AN

AUTHORIZED SERVICE REPRESENTATIVE.

CAUTION: The filters have been designed to provide optimal system performance by catching any debris that may enter the supply lines throughout use.

Semi annual replacement of both the air and water filters ensures the life of your system.

• Remove the filter cover and locate the air and water filters. (fig.1).

AMMF16R Rev. A 07/10 9

• Push the connector ring and pull out the air hose from the one-touch connector and the water hose from the water flow control valve.

• Disassembly the screw of the one-touch connector and water flow control valve

• The filters are connected to the system via “Push-In” connectors for ease of service. Push the connector and pull the hose. (fig.2).

• Dispose of old filter.

• Remove filter from package and orient the directional arrow so that the flow direction is towards the left.

(fig.3)

• Push the hose into the push-in connector to connect the filters. (fig.4)

• Assembly the one-touch connector and water flow control valve.

• Reinstall filter cover. (fig.5)

CAUTION: IMPROPER PLACEMENT OF THE FILTER CAN DEGRADE SYSTEM

PERFORMANCE.

• Remove filter from package and orient the directional arrow so that the flow direction is towards the left (fig.3).



Pages:   || 2 |


Similar works:

«The Lab Renderer for Unity Contents Introduction Single-Pass Forward Rendering and MSAA Adaptive quality Custom Shaders GPU Flushing Quick Start Guide Elements Valve Menu Items Enable & Disable Scene Auto-Rendering Convert Active Materials to/from Valve or Unity Shaders Convert All Materials to/from Valve or Unity Shaders Ensure Consistency in Valve Materials Valve Camera Component Lights & Shadows Adaptive Quality Helper Debug Information Valve Realtime Light Component Valve VR Standard Shader...»

«ZEBRALAND by Marlene Röder © 2009 Ravensburger Buchverlag, Germany Sample translation by Tammi Reichel, APE International, Richmond, VA p. 5 – 14 And whosoever diggeth a pit Shall fall in it And whosoever diggeth a pit Shall bury in it Bob Marley, Small Axe Zebraland I’m standing on the roof of the gym, spray-painting a zebra on the back wall of my old school. My spray can hisses as I add the last black line, and the smell of fresh paint surrounds me. Gravel crunches under my sneakers as...»

«KNIGHTS OF COLUMBUS One Life One Rose Our Lady of Guadalupe Silver Rose Program Our Lady of Guadalupe The Events of Guadalupe E arly on a cold Saturday morning (December 9, 1531), Juan Diego, baptized into the faith as an adult in 1523, was on his way to assist at Mass about two and a half miles from Tlatleloco, where there was a church and where the Spaniards had concluded their conquest of Mexico ten years earlier. Suddenly he heard beautiful music and a woman’s voice calling to him from...»

«Adaptation Case Study #1: Frontiers North Adventures SECTOR: TOURISM Location: Churchill, Manitoba Adaptation Case Study #1: Frontiers North Adventures SECTOR: TOURISM Location: Churchill, Manitoba DISCLAIMER This paper was prepared by the Chartered Professional Accountants of Canada (CPA Canada) as non-authoritative guidance. CPA Canada and the authors do not accept any responsibility or liability that might occur directly or indirectly as a consequence of the use, application or reliance on...»

«IN THE UNITED STATES DISTRICT COURT FOR THE NORTHERN DISTRICT OF TEXAS DALLAS DIVISION SECURITIES AND EXCHANGE COMMISSION, : :Plaintiff, : : vs. : Civil Action No. : 3:08-CV-0499-N W FINANCIAL GROUP, LLC, : ADLEY H. ABDULWAHAB a/k/a Adley Wahab, : MICHAEL K. WALLENS, SR., and : MICHAEL K. WALLENS, JR. : : Defendants, : : PLAINTIFF SECURITIES AND EXCHANGE COMMISSION’S MEMORANDUM IN SUPPORT OF MOTION FOR SUMMARY JUDGMENT AGAINST DEFENDANTS W FINANCIAL GROUP, LLC, ADLEY H. ABDULWAHAB a/k/a ADLEY...»

«1 Symposium on Innovation and Inclusive Growth 20-21 March 2014 Biographies SYMPOSIUM ON INNOVATION AND INCLUSIVE GROWTH March 20th-21st, 2014 Paris, France Biographies Dr. Natalia Agapitova Coordinator for the Development Marketplace Program, World Bank. Dr. Natalia Agapitova is the Coordinator for the Development Marketplace Program at the World Bank. She has worked extensively with operational and analytical aspects of innovation and social entrepreneurship since 1997, including twelve years...»

«CALL FOR PROPOSALS CONCERNING PROJECTS OF COMMON INTEREST UNDER THE CONNECTING EUROPE FACILITY IN THE FIELD OF TRANS-EUROPEAN TELECOMMUNICATION NETWORKS CEF TELECOM CALLS 2016 CEF-TC-2016-3: Europeana 1. CALL CONTEXT The general context for this call for proposals is defined in Section 3.1 of the 2016 CEF Telecom work programme1 as published on the call page on the Innovation and Networks Executive Agency (INEA) website2. 2. BACKGROUND AND RATIONALE The background and rationale for this call...»

«Capitalism and Society Volume 3, Issue 2 2008 Article 3 Household Debt in the Consumer Age: Source of Growth—Risk of Collapse Barry Z. Cynamon∗ Steven M. Fazzari† ∗ University of Chicago, bcynamon@uchicago.edu † Washington University in St. Louis, fazz@wustl.edu Copyright c 2008 The Berkeley Electronic Press. All rights reserved. Household Debt in the Consumer Age: Source of Growth—Risk of Collapse∗ Barry Z. Cynamon and Steven M. Fazzari Abstract The 2008 U.S. financial upheaval...»

«Menu Hadley Farms Meeting House La Quinta Inns and Suites 41 Russell Street 100 Congress Street Hadley MA 01035 Springfield MA 01104 (413) 750-3101 sales@pvhg.com www.hadleyfarmsmeetinghouse.com www.pvhg.com General Conditions China, silverware, glassware, linens, tables, chairs, and stainless steel chaffers are included unless otherwise noted on the menu. House linens and basic décor for food areas are included. All tables will be covered with your choice of white, ivory, or black...»

«CHAPTER 3 Immigrants and Their Media CHAPTER OBJECTIVES By the end of this chapter, you will have learned more about: • The differences between immigrants and other types of migrants.• How migration experiences are different depending on where people have come from and where they have settled.• The roles that ethnic media play in immigration and settlement. Why Immigration Matters What percentage of the world’s population do you think lives outside of the country where they were born?...»

«MD Research News Issue 207 Monday 17 November, 2014 This free weekly bulletin lists the latest published research articles on macular degeneration (MD) and some other macular diseases as indexed in the NCBI, PubMed (Medline) and Entrez (GenBank) databases. If you have not already subscribed, please email Rob Cummins at research@mdfoundation.com.au with ‘Subscribe to MD Research News’ in the subject line, and your name and address in the body of the email. You may unsubscribe at any time by...»

«Exercise therapy and the treatment of mild or moderate depression in primary care Contents | Up and running? Contents i) Foreword............................................................................ 2 ii) Acknowledgements................................................................. 3 iii) Executive summary.......................»





 
<<  HOME   |    CONTACTS
2016 www.dissertation.xlibx.info - Dissertations, online materials

Materials of this site are available for review, all rights belong to their respective owners.
If you do not agree with the fact that your material is placed on this site, please, email us, we will within 1-2 business days delete him.